CJ-F 1000 Series Conventional Fire Alarm Control Panel

Model: CJ-F1004, CJ-F1008, CJ-F1016

The CJ-F1000 Series Conventional Fire Alarm Control Panel is a 24 volt, four, eight, sixteen-zone, Class B, Conventional Fire Alarm Control Panel. Designed exclusively to meet the latest market requirements and future ULC codes, the highly cost-effective CJ-F1000 Series can be used in a variety of low- to mid-sized applications.

FEATURES                                                                                                                                                                         

l         Four to Sixteen Style B (Class B) Initiating Device Circuits (IDCs).

– All zones accept two-wire smoke detectors and any normally-open contact devices.

– Zones 1 - 16 configured as general alarm zones.

l         All circuits are power-limited and supervised, meeting the latest ULC requirements using fuseless technology.

l         Two built-in, Style Y (Class B) Notification Appliance (Signal) Circuits (NACs).

l         NACs may be programmed:

– Silenceable.

– Non-Silenceable.

– Auto-Silence (program 5 to 20 minutes).

l         1.25 amps of NAC power.

l         3.0 amps of total system power.

l         Alarm, Trouble and Supervisory, relay output.

l         24-volt operation.

l         Resettable four-wire smoke detector power @ 500 mA.

l         Non-resettable power @ 500 mA.

l         Integral battery charger capable of charging up to 18 AH batteries (batteries over 4 AH require use of the external battery backbox, or ULC listed equivalent).

l         Disable/Enable control per IDC.

l         Reverse polarity protection.

l         Control buttons:

– Mode

– Test

– ACK (Acknowledge) Alarm Silence

– Reset

l         LED indicators:

– AC Power(green & yellow LED)

– Fire Alarm(red LED)

– Trouble(yellow LED)

– Supervisory(yellow LED)

– Signal Silence(yellow LED)

– Battery Power(green & yellow LED)

– Zone Disable(yellow LED)

– NAC Fault(yellow LED)

– NAC Disable(yellow LED)

– Zone Alarm(one for each zone) (red LED)

– Zone Trouble(one for each zone) (yellow LED)

– Earth Fault (on circuit board)

– Battery Fault (on circuit board)

–        Charger Fault (on circuit board)

SPECIFICATIONS                                                                                                                                                            

l         AC POWER

– 90～270 VAC, 50 Hz, 2.0 amps.

– Wire size: minimum 14 AWG (2.0 mm2) with 600-volt insulation.

l         BATTERY

– Sealed lead-acid batteries only.

– Maximum charging circuit: 27.6VDC @ 0.8 amp for normal flat charge.

– Maximum battery charger capacity: 18AH battery.

NOTE: two 4AH batteries can be housed in the cabinet. Larger

batteries require a separate battery box.

l         Total 24 V system power: 3.0 amps.

l         Notification appliance (signal) power: 2.5 amps.

l         Maximum current per NAC: 1.25 amps (expandable to 2.5amps).

l         Maximum battery charging capability: 18 AH.

Auxiliary Outputs

l         Resettable four-wire smoke detector power @ 500 mA.

l         Non-resettable power @ 500 mA.

NOTE: Total current for auxiliary power outputs and two NACs must not exceed 3.0 amps. .

l         Integral Form-C Alarm, Trouble and Supervisory relays, rated at: 2.0 amps @ 30 VDC (resistive), 2.0 amps @ 30VAC (resistive).

CABINET AND MOUNTING

CABINET PHYSICAL DIMENSIONS: 40.0 cm high x 35.0 cm wide x 11.5 cm deep.

CARTON PACKAGE DIMENSIONS: 48.0 cm high x 42.0 cm wide x 18.5 cm deep.

CABINET NET WEIGH: 6.0 Kg. (without batteries).

CABINET GROSS WEIGH: 6.6 Kg. (without batteries).

MOUNTING: The cabinet mounts using two key slots at the top of the back and two additional 6.5mm diameter holes at the bottom.